• Steel suppliers in Chennai

Cold Work Tool Steel D-2

D2 steel is an air hardening, high-carbon, high-chromium tool steel. It has high wear and abrasion resistant properties. It is heat treatable and will offer a hardness in the range 55-62 HRC, and is machinable in the annealed condition. D2 steel shows little distortion on correct hardening. D2 steel’s high chromium content gives it mild corrosion resisting properties in the hardened condition.

Cold-work tool steels include the high-carbon, high-chromium steels or group D steels. These steels are designated as group D steels and consist of D2, D3, D4, D5, and D7 steels. These steels contain 1.5 to 2.35% of carbon and 12% of chromium. Except type D3 steel, all the other group D steels include 1% Mo and are air hardened. Type D3 steel is oil-quenched; though small sections can be gas quenched after austenitization using vacuum. As a result, tools made with type D3 steel tends to be brittle during hardening. Type D2 steel is the most commonly used steel among the group D steels.

Chemical Composition
ElementMinMax
Carbon, C1.551.75
Manganese, Mn0.200.40
Silicon, Si0.250.40
Molybdenum, Mo0.500.70
Chromium,Cr11.0012.00
W0.400.60
Co0.50
Chemical Composition
PropertiesMetricImperial
Density7.7 x 1000 kg/m30.278 lb/in3
Melting point1421°C2590°F
Thermal Properties
PropertiesConditions
T (°C)Treatment
Thermal expansion10.4 x 10 -6 /ºC20-100-
Heat Treatment

D2 steels should be preheated very slowly to 815ºC (1500ºF) and then temperature can be increased to 1010ºC (1850ºF). They are then held at 1010ºC (1850ºF) for 20 to 45 minutes and air cooled (air quenched).

Annealing

D2 is supplied in the annealed and machineable condition. Re-annealing will only be necessary if the steel has been forged or hardened by the toolmaker. To anneal, heat slowly and uniformly to 900°C. Soak for three to four hours and allow to cool in the furnace to room temperature. Re-heat to 800-1040°C and again soak for three to four hours. Allow to cool in the furnace to room temperature.

Tempering

D2 steels can be tempered at 204ºC (400ºF) for achieving Rockwell C hardness of 61 and at 537ºC (1000ºF) for a Rockwell C hardness of 54.

Applications

A popular grade for toolmakers, D2 is used in a wide variety of tool making applications. Typical applications include blanking dies and punches for sheet in stainless steel, brass, copper, zinc and hard abrasive materials generally. Other application include deep drawing dies, cupping dies, forming dies, sheet metal forming rolls, shear blades for strip and sheet including flying shears, circular cutters for cold rolled strip, trimmer dies, thread rolling dies, cold extrusion dies, broaches, plug gauges, ring gauges, special taps, straybolt taps, brick and tile mould liners, master hobs for cold hobbing plastic moulds and cut moulds for plastics

Final Grinding

Select the correct grade of wheel in consultation with the grinding wheel manufacturer. Ensure the grinding wheel is in good condition by means of a suitable dressing tool. Wet grinding is a preferable option using a copious supply of coolant. If dry grinding is resorted to then use a very soft wheel.

Hardening

It is preferable to heat the tools in a controlled atmosphere. If this is not possible, pack hardening is recommended. A reducing atmosphere is desirable. Pre heat the D2 tool steel component to 750-800°C. and allow to soak at this temperature. The tools may then be brought up to 1000-1040°C for air cooling, or 980°C for oil quenching. Soak thoroughly at the temperature for thirty minutes per 25mm of ruling section, then cool or quench accordingly. It is important not to exceed 1020°C when heating for hardening.

Stress Relieving

When tools made from D2 tool steel are heavily machined, ground or otherwise subjected to cold work, the relief of internal strains is advisable before hardening to minimise the possibility of distortion. Stress relieving should be done after rough machining. To stress relieve, heat the component to 600-650°C. Soak well and cool in the furnace or in air. The tools may then be finish machined before hardening.